PAGE 1
Electric Airless Sprayer OWNERS MANUAL X5, X7, ProX17, ProX19, ProX21 3A3208B 3A3208B EN EN FIRE AND EXPLOSION HAZARD X5/X7 Models: • Use only non-flammable or water-based materials, or non-flammable paint thinners. Do not use • materials having flash points lower than 100° F (38° C). This includes, but is not limited to, acetone, xylene, toluene, or naphtha. For more information about your material, request Safety Data Sheet (SDS) from the supplier.
PAGE 2
Before You Spray Before You Spray Review Warnings for Important Safety Information Important! Read carefully and practice good safety habits. Review Manual & Watch Videos Scan QR code for Operational Video or go to magnum.graco.com/magop Related Manuals Gun: 312830 (SG) ProXChange™ Pump: 3A3172 (ProX only) Models 3000 psi (207 bar, 20.7 MPa) Maximum Working Pressure VAC Model X5 Stand (Series) 262800 (E) 17K437 (A) X7 110474 Certified to CAN/CSA C22.2 No.
PAGE 3
Contents Contents Before You Spray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Know Your Sprayer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
PAGE 5
Warnings FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion: X5/X7 Models: • Do not spray or clean with materials having flash points lower than 100°F (38° C). Use only • • non-flammable or water-based materials, or non-flammable paint thinners. For complete information about your material, request the Safety Data Sheet (SDS) from the material distributor or retailer.
PAGE 6
Warnings SKIN INJECTION HAZARD High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that injection occurs, get immediate surgical treatment. • Do not aim the gun at, or spray any person or animal. • Keep hands and other body parts away from the discharge. For example, do not try to stop leaks with any part of the body. • Always use the nozzle tip guard. Do not spray without nozzle tip guard in place. • Use Graco nozzle tips.
PAGE 7
Warnings PRESSURIZED ALUMINUM PARTS HAZARD Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage. • Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents. • Do not use chlorine bleach. • Many other fluids may contain chemicals that can react with aluminum.
PAGE 8
Know Your Sprayer Know Your Sprayer X5 Stand Models F U E B D A W T C N P G H J Q K M L ti28222a A B C D E F G H J K L 8 PushPrime™ Button Prime/Spray Valve Pressure Control Knob ON/OFF Switch Suction Tube Drain Tube (with diffuser) Airless Spray Gun Reversible Spray Tip Tip Guard Gun Trigger Lock Gun Fluid Inlet Fitting M N P Gun Fluid Filter (inside handle) Pump Pump Fluid Outlet Fitting (airless hose connection) Q Airless Hose T Inlet Strainer U Power Cord Model/Serial Tag (Not shown, loca
PAGE 9
Know Your Sprayer X7 Cart Model G H J K Q M N L B D P A C S U F E T ti28223a A B C D E F G H J K L PushPrime™ Button Prime/Spray Valve Pressure Control Knob ON/OFF Switch Suction Tube Drain Tube (with diffuser) Airless Spray Gun Reversible Spray Tip Tip Guard Gun Trigger Lock Gun Fluid Inlet Fitting 3A3208B M N P Gun Fluid Filter (inside handle) Pump Pump Fluid Outlet Fitting (airless hose connection) Q Airless Hose S Pail Hanger T Inlet Strainer U Power Cord Model/Serial Tag (Not shown, l
PAGE 10
Know Your Sprayer ProX Stand Models F D Q E U Z W T G H V J C R K N X M P ti27116a A B C D E F G H J K L M N 10 L PushPrime™ Button Prime/Spray Valve Pressure Control Knob ON/OFF Switch Suction Tube Drain Tube (with diffuser) Airless Spray Gun Reversible Spray Tip Tip Guard Gun Trigger Lock Gun Fluid Inlet Fitting Gun Fluid Filter (inside handle) ProXChange™ Pump (behind Easy Access Door) B A P Pump Fluid Outlet Fitting (airless hose connection) Q Airless Hose R InstaClean™ Fluid Filter
PAGE 11
Know Your Sprayer ProX Cart Models V C R D N P A S X B Z G H U J K F M E L Q T ti27117a A B C D E F G H J K L M N PushPrime Button Prime/Spray Valve Pressure Control Knob ON/OFF Switch Suction Tube Drain Tube (with diffuser) Airless Spray Gun Reversible Spray Tip Tip Guard Gun Trigger Lock Gun Fluid Inlet Fitting Gun Fluid Filter (inside handle) ProXChange Pump (behind Easy Access Door) 3A3208B P Pump Fluid Outlet Fitting (airless hose connection) Q Airless Hose R InstaClean Fluid Filte
PAGE 12
Setup Setup When unpacking sprayer for the first time or after long term storage perform setup procedure. Assemble Your Sprayer 1. Connect Graco airless hose to fluid outlet. Use wrench to tighten securely. ti25197a 6. Turn pressure control knob all the way left (counter-clockwise) to lowest setting. ti27122a 2. Connect other end of hose to gun. ti27493a 7. ti25199a 3. Use two wrenches to tighten securely. If hose is already connected, make sure connections are tight. 4. Engage trigger lock.
PAGE 13
Start Up Start Up ti25198b 3. Pressure Relief Procedure Turn pressure control knob to lowest setting. Follow the Pressure Relief Procedure whenever you see this symbol. This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection or splashed fluid, follow the Pressure Relief Procedure whenever sprayer is stopped and before sprayer is cleaned or checked, and before equipment is serviced. 1. ti27493a 4.
PAGE 14
Start Up 7. If you suspect the spray tip or hose is clogged or that pressure has not been fully relieved: a. b. c. VERY SLOWLY loosen the tip guard retaining nut or the hose end coupling to relieve pressure gradually. Loosen the nut or coupling completely. Clear airless hose or spray tip obstruction. See Clear Tip Clog, page 18. Flush Storage Fluid 6. Turn Prime/Spray valve down to PRIME position. ti27120a 7. Plug power supply cord into a properly grounded electrical outlet. 8.
PAGE 15
Start Up 11. When sprayer starts pumping, flushing solvent and air bubbles will be purged from system. Allow fluid to flow out of drain tube, into waste pail, for 30 to 60 seconds. 12. Turn ON/OFF switch to OFF position. NOTE: Some fluids may prime faster if the ON/OFF Switch is momentarily turned off so the pump can slow and stop. Turn ON/OFF switch on and off several times if necessary. Fill Gun and Hose 1. Hold gun against waste pail. Point gun into waste pail.
PAGE 16
How to Spray How to Spray ti27143a Spray Tip Installation b. To prevent spray tip leaks make certain spray tip and tip guard are installed properly. 1. Perform Pressure Relief Procedure, page 13. 2. Engage trigger lock. 3. Verify spray tip and tip guard parts are assembled in the order shown. SPRAY TIP TIP GUARD ti27145a RUBBER GASKET/ METAL SEAL c. 4. RETAINING NUT a. Spray tip must be pushed all the way into the tip guard. Turn spray tip to push down.
PAGE 17
How to Spray Adjust Pressure Control The pressure control knob allows for infinite pressure adjustment. To reduce overspray, always start at the lowest pressure setting and increase pressure to the minimum setting that results in an acceptable spray pattern. 3000 psi (207 bar, 20.7 MPa) 1500 psi (103 bar, 10.3 MPa) 500 psi (34.5 bar, 3.5 MPa) ti5597b To select function, align symbol on pressure control knob with setting indicator on sprayer.
PAGE 18
How to Spray Triggering Gun • Pull trigger after starting stroke. Release trigger before end of stroke. Gun must be moving when trigger is pulled and released. Clear Tip Clog Material may need to be thinned. If material needs to be thinned follow manufacturer’s recommendations. In the event that particles or debris clog the spray tip, this sprayer is designed with a reversible spray tip that quickly and easily clears the particles without disassembling the sprayer.
PAGE 19
Cleanup Cleanup Cleaning the sprayer after each use results in a trouble free start up the next time the sprayer is used. 5. Place empty waste and flushing fluid pails side by side. 6. Place suction tube in flushing fluid. Use water for water based paint and mineral spirits or compatible oil-based flushing solvent for oil-based paint. Place drain tube in waste pail. 7. Turn pressure control knob to the Prime/Clean setting.
PAGE 20
Cleanup 11. Turn ON/OFF switch to OFF position. NOTE: Step 12 is for returning paint in hose to paint pail. One 50 ft (15 m) hose holds approximately 1 quart (1 liter) of paint. 12. To recover paint in hose, point gun into paint pail while holding gun firmly to the pail. a. b. c. d. e. A Disengage trigger lock. Pull and hold gun trigger. Turn Prime/Spray valve horizontal to SPRAY position. Turn ON/OFF switch to ON position.
PAGE 21
Cleanup 6. Turn pressure control knob to the Prime/Clean setting. 11. Turn ON/OFF switch to ON position. 12. Open Power Flush attachment valve. 13. Circulate water through sprayer, into waste pail, for 20 seconds. 14. Turn ON/OFF switch to OFF position. ti27135a NOTE: Step 15 is for returning paint in hose to paint pail. One 50 ft (15 m) hose holds approximately 1 quart (1 liter) of paint. 7. 15. To recover paint in hose, point gun into paint pail while holding gun firmly to the pail.
PAGE 22
Cleanup 6. ti25196b 19. Turn Prime/Spray valve down to PRIME position. a. Install closed (square) end of InstaClean Fluid Filter (C) in sprayer. b. Screw outlet fitting (B) into sprayer. Tighten outlet fitting and reconnect hose (A) to sprayer. Use two wrench to tighten securely. ti27122a ti27120a 20. Turn ON/OFF switch to OFF position. Clean the Gun 1. Cleaning InstaClean™ Fluid Filter (ProX only) Clean gun fluid filter with water or flushing fluid and a brush every time you flush the system.
PAGE 23
Storage Storage With proper storage, the sprayer will be ready to use the next time it is needed. 4. Engage trigger lock. ti25196b Short Term Storage (up to 2 days) 1. Perform Pressure Relief Procedure, page 13. 2. Leave suction tube and drain tube in paint pail. 5. Leave gun attached to hose. 6. Remove tip and guard and clean with water or flushing fluid and a brush. 7. Wipe paint off outside of gun using a soft cloth moistened with water or flushing fluid.
PAGE 24
Storage 3. Turn Prime/Spray valve down to PRIME position. 8. Leave gun attached to hose. 9. Remove tip and guard and clean with water or flushing fluid and a brush. 10. Wipe paint off outside of gun using a soft cloth moistened with water or flushing fluid. ti27120a 4. Turn ON/OFF switch to ON position. 5. Turn pressure control knob clockwise until the pump turns on. 6. When storage fluid comes out of drain tube (5-10 seconds) turn ON/OFF switch to OFF position. 7.
PAGE 25
Reference Reference Understanding Tip Number Spray Tip Selection The last three digits of tip number (i.e.: 221413) contain information about hole size and fan width on surface when gun is held 12 in. (30.5 cm) from surface being sprayed. Selecting Tip Size Spray tips come in a variety of hole sizes for spraying a range of fluids. Your sprayer includes a tip for use in most paint spraying applications.
PAGE 26
Reference Lacquer Conversion Kit • To spray lacquers with the ProX17 or ProX19, you must purchase a lacquer conversion kit, and follow Static Grounding Instructions (Oil-Based materials), page 26, when using oil-based materials. See ProX17 and ProX19 parts list, page 41 or 45. The X5 and X7 must not be used with lacquers. Static Grounding Instructions (Oil-Based materials) To avoid fluid splashing back on your skin or into your eyes, always aim gun at inside wall of pail.
PAGE 27
Reference Always ground a metal pail: connect a ground wire to the pail. Clamp one end to the pail and the other end to a true earth ground such as a water pipe. To maintain ground continuity when sprayer is flushed or pressure is relieved: hold metal part of spray gun firmly to the side of a grounded metal pail, then trigger the gun.
PAGE 28
Reference Quick Reference Page 10 Name Description A Prime/Spray Valve • • B C PushPrime Button Pressure Control Knob D E F ON/OFF Switch Suction Tube Drain Tube G H Airless Spray Gun Reversible Spray Tip J K L M N Tip Guard Gun Trigger Lock Gun Fluid Inlet Fitting Gun Fluid Filter Pump P Q Pump Fluid Outlet Fitting Airless Hose R InstaClean™ Fluid Filter (ProX only) S T U V Pail Hanger Inlet Strainer Power Cord Easy Access Door (ProX only) W Suction Tube Drip Cup X Pump Removal Tool
PAGE 29
Maintenance Maintenance Routine maintenance is important to ensure proper operation of your sprayer. Activity Interval Inspect motor shroud openings for blockage. Daily or each time you spray Inspect/clean InstaClean filter (ProX only), fluid inlet strainer, Daily or each time you spray and gun filter. NOTICE Protect the internal drive parts of this sprayer from water. Openings in shroud allow cooling of mechanical parts and electronics inside.
PAGE 30
Maintenance 4. Slide pump assembly off the mounting pins. Inlet Valve Removal An integrated tool is included in the frame to remove the inlet valve assembly from the pump. If you suspect that the inlet valve is clogged or stuck, remove the valve assembly and clean or replace. 1. Remove suction tube or hopper from sprayer. 2. Insert pump inlet into frame and loosen the inlet valve. Remove inlet valve.
PAGE 31
Maintenance Pump Installation 1. b. Slide pump assembly onto the mounting pins. 2. Push on pump rod to slide pump assembly back on to mounting pins. Swing easy access door closed while pushing the entire door towards the inlet end of the pump. 1 2 3 ti27036a a. Move pump rod up or down until cap is level with the opening in the yoke. ti27478a 3. Install hopper if it was removed and any hoses removed earlier. 4. Plug sprayer into power source.
PAGE 32
Troubleshooting Troubleshooting 3. Check everything in this Troubleshooting Table before you bring the sprayer to an authorized service center. Have a Question? Call toll-free: 1. 2. Follow Pressure Relief Procedure, page 13, before checking or repairing. Solutions at the beginning of each problem listed are the most common. Problem Motor does not run: (verify sprayer is plugged in, and ON/OFF switch is on) 32 1-888-541-9788 Or visit us at: www.magnum.graco.
PAGE 33
Troubleshooting Problem Sprayer runs, but pump does not prime or looses prime while in use. (Pump cycles but does not pump paint or build pressure.) 3A3208B Cause Solution Inlet valve check ball is stuck. Press PushPrime button to dislodge the ball allowing pump to prime properly, OR Power Flush sprayer, see page 20. Prime/Spray valve is in SPRAY position. Turn Prime/Spray valve down to PRIME position until paint exits drain tube. The pump is now primed. Pump was not primed with flushing fluid.
PAGE 34
Troubleshooting Problem Pump is primed, but can not achieve good spray pattern. Cause Solution Spray tip may be partially clogged. Clear spray tip clog. See page 18. Reversible spray tip is in UNCLOG position. Rotate arrow-shaped handle on spray tip so it points forward to SPRAY position. See page 18. Debris in paint. Strain the paint. See page 26. Pressure is set too low. Align pressure control knob setting indicator to desired spray setting. See page 17.
PAGE 35
Troubleshooting Problem When paint is sprayed, it runs down the wall or sags. Cause Material is going on too thick. Solution Move gun faster. Choose a spray tip with smaller hole size. Choose spray tip with wider fan. Make sure gun is far enough from surface. When paint is sprayed, coverage is inadequate. Material is going on too thin. Move gun slower. Choose spray tip with larger hole size. Choose spray tip with narrower fan. Make sure gun is close enough to surface.
PAGE 36
X5: 262800, 17K437 Stand Sprayer Parts X5: 262800, 17K437 Stand Sprayer Parts 10b 1 5 2 22a 4 22 10 13a 41 3 4 6 51 1 5 13 33b 33c 33a 33 20 19b 10a 17 48 19a 2 12 29c 29a 29b 31 19 52 8 8a 8b 40 37 39 30 36 29 16 36 38 Ref. 16b 6 16a 35 34 ti28224a Torque 1 20-25 in-lb (2.3-2.8 N•m) 2 26-32 in-lb (2.9-3.6 N•m) 3 25-35 in-lb (2.8-4.0 N•m) 4 80-90 in-lb (9.0-10.0 N•m) 5 12-16 in-lb (1.4-1.8 N•m) 6 36-42 in-lb (4.0-4.
PAGE 37
X5: 262800, 17K437 Stand Sprayer Parts 262800, 17K437 Stand Sprayer Parts List - Ref.
PAGE 38
X7: 262805 Cart Sprayer Parts X7: 262805 Cart Sprayer Parts 38 40 39 5 10c 3 22a 22 2 10b 1 19a 41 6 2 10 10a 42 10d 13a 3 44 18 33c 1 33b 6 33a 5 33 13 20 16a 17 13a 48 35 2 12 8 19 37 8a 36 31 8b 29c 29a 29b 16b 43 16 29 27 26 51 25 52 28 ti28225a Ref. 38 30 24 23 Torque 1 20-25 in-lb (2.3-2.8 N•m) 2 45-55 in-lb (5.0-6.2 N•m) 3 25-35 in-lb (2.8-4.0 N•m) 4 80-90 in-lb (9.0-10.0 N•m) 5 12-16 in-lb (1.4-1.8 N•m) 6 36-42 in-lb (4.0-4.
PAGE 39
X7: 262805 Cart Sprayer Parts 262805 Cart Sprayer Parts List Ref.
PAGE 40
ProX17: 17G177, 17K438, ProX19: 17G179 ProX17: 17G177, 17K438, ProX19: 17G179 Stand Sprayer Parts Ref. Torque 1 140-160 in-lb (16-18 N•m) 2 30-35 in-lb (3.5-4.0 N•m) 3 110-120 in-lb (12-14 N•m) 4 45-55 in-lb (5-6 N•m) 25 31 24 2 9 8 30 56 13 17 15 15a 2 16 18 2 1a 6 1 See page 48.
PAGE 41
ProX17: 17G177, 17K438, ProX19: 17G179 17G177, 17K438, 17G179 Stand Sprayer Parts List Ref.
PAGE 42
ProX21: 17G181 Stand Sprayer Parts ProX21: 17G181 Stand Sprayer Parts Ref. Torque 1 140-160 in-lb (16-18 N•m) 2 30-35 in-lb (3.5-4.0 N•m) 3 110-120 in-lb (12-14 N•m) 2 8 31 25 9 24 2 15 56 30 16 2 18 15a See page 48.
PAGE 43
ProX21: 17G181 Stand Sprayer Parts 17G181 Stand Sprayer Parts List Ref. 1 1a 2 3 4 6 Part 17K684 16X980 17J869 17J173 17J864 117493 Description MOTOR, 120V FAN KIT, gear and yoke CORD, power KIT, yoke SCREW, mach, hex, washer head 7 17J875 KIT, pump complete 17K688 SHIELD, motor, blue 8 includes 9 and labels 9 118444 SCREW, mach, hwhd 10-24 x 0.5 in.
PAGE 44
ProX17: 17G178, ProX19: 17G180, 17K439 ProX17: 17G178, ProX19: 17G180, 17K439 Cart Sprayer Parts Ref. Torque 2 30-35 in-lb (3.5-4.0 N•m) 3 110-120 in-lb (12-14 N•m) 4 45-55 in-lb (5-6 N•m) 31 2 8 9 40 37 30 2 41 56 1 17 13 16 2 18 15 15a 2 1a 4 10a 2 9 10b 3 12 42 54 3 10 22 4 7 36 27 38 19 16 14 43 39 48 35 See page 48.
PAGE 45
ProX17: 17G178, ProX19: 17G180, 17K439 17G178, 17G180, 17K439 Cart Sprayer Parts List Description Ref. Part Qty. 1 MOTOR, 120V 17K285 ProX17 1 17F756 ProX19 1 1a 287770 FAN 1 2 17J863 KIT, gear and yoke 1 3 17J173 CORD, power 1 4 17J864 KIT, yoke 1 7 17J874 KIT, pump complete 1 17J865 SHIELD, motor, blue 8 1 includes 9 and labels 9 118444 SCREW, mach, hwhd 3 10-24 x 0.5 in.
PAGE 46
ProX21: 17G182 Cart Sprayer Parts ProX21: 17G182 Cart Sprayer Parts Ref. Torque 2 30-35 in-lb (3.5-4.0 N•m) 3 110-120 in-lb (12 -14 N•m) 2 9 31 8 41 30 2 16 2 1a 15a 18 15 17 13 56 2 2 1 4 10a 9 10b 10 27 12 3 3 7 42 49 50 34 14 51 35 22 52 26 3 16 38 53 See page 48.
PAGE 47
ProX21: 17G182 Cart Sprayer Parts 17G182 Cart Sprayer Parts List Description Ref. Part Qty. 1 17K684 KIT, repair, motor, 120V 1 includes 1a 1a 16X980 FAN 1 2 17J869 KIT, gear and yoke 1 3 17J173 CORD, power 1 4 17J864 KIT, yoke 1 7 17J875 KIT, pump complete 1 17K688 SHIELD, motor, blue 8 1 includes 9 and labels 9 118444 SCREW, mach, hwhd 3 10-24 x 0.5 in.
PAGE 48
ProXChange Pump (ProX only) ProXChange Pump (ProX only) Ref. Torque 1 140-160 in-lb (16-18 N•m) 2 30-35 in-lb (3.4-4.
PAGE 49
ProXChange Pump (ProX only) Pump Parts List i Ref. 1 2 3 4 5 6 6a 7 7a 7b 8 9 10 11 12 Part 17G447 17D364 128336 105445 117501 Description HOUSING, pump GUIDE, ball SPRING, compression BALL, 0.5 in. SCREW, mach, slot HWH KIT, inlet housing 17J876 ProX17, ProX19 17J877 ProX21 124582 O-ring 17J878 KIT, PushPrime includes 7a, 7b 16P303 PACKING, O-ring 17G540 LABEL, PushPrime 235014 VALVE, drain, assy 224807 BASE, valve 187625 HANDLE, valve, drain 111600 PIN, grooved 288747 KIT, filter 3A3208B Qty.
PAGE 50
Wiring Diagram - 110/120V Wiring Diagram - 110/120V X5/X7: ON/OFF SWITCH BLACK WHITE GREEN BLACK PRESSURE SWITCH BLACK MOTOR ti14050a ProX: M ti27233a 50 3A3208B
PAGE 51
Technical Specifications Technical Specifications Sprayer Maximum fluid working pressure Maximum Delivery X5 X7 ProX17 ProX19 ProX21 Maximum Tip Size X5 X7 ProX17 ProX19 ProX21 Fluid Outlet npsm Generator Minimum Power Requirements X5, X7 ProX17, ProX19 ProX21 Dimensions Height X5 X7 ProX17, ProX19 Stand ProX21 Stand ProX17, ProX19 Cart ProX21 Cart Length X5 X7 ProX17, ProX19 Stand ProX21 Stand ProX17, ProX19 Cart ProX21 Cart 3A3208B US Metric 3000 psi 207 bar, 20.7 MPa 0.27 gpm 0.31 gpm 0.34 gpm 0.
PAGE 52
Technical Specifications US Metric 12.4 in. 15.3 in. 13.2 in. 13.5 in. 17.2 in. 20.6 in. 31.5 cm 38.9 cm 33.5 cm 34.3 cm 43.7 cm 52.3 cm Width X5 X7 ProX17, ProX19 Stand ProX21 Stand ProX17, ProX19 Cart ProX21 Cart Weight X5 X7 ProX17, ProX19 Stand ProX21 Stand ProX17, ProX19 Cart ProX21 Cart Storage temperature range 16.5 lb. 26.5 lb. 27.3 lb. 25.0 lb. 37.5 lb. 49.5 lb. 7.5 kg 12.0 kg 12.4 kg 11.3 kg 17.0 kg 22.
PAGE 53
Notes Notes 3A3208B 53
PAGE 54
Notes Notes 54 3A3208B
PAGE 55
Graco Standard Warranty Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
PAGE 56
Graco Information For the latest information about Graco products, visit www.graco.com. For patent information, see www.graco.com/patents. TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor. All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English.